CNC laser cutting machine fault diagnosis, elimination should follow the basic original

CNC laser cutting machine fault diagnosis, elimination should follow the basic principles of:Principle of CNC laser cutting machine is on the basis of the numerical control machine tool, the use of outside light path will be imported, produced by the laser beam through focusing on material surface, forming a molten pool in the surface of materials, or directly to the material for gasification, and then use after cutting head diversion of auxiliary gas breathed from slag, and thus reach the stable cutting effect.Any parts or hinder the process status conditions are fault judgment standard.But the basic troubleshooting standards is as follows:
(1) the first plan after operation
When a fault, you should calm down and carefully ask operator failure phenomenon, and after the fault symptoms, carefully analyze possible reasons, and solutions.
(2) simple after complex test first principle
When there is a variety of phenomena are intertwined coverage, temporarily do not know how to start, should first solve the problem of easy, after solving the problem of difficult.
(3) after the first external internal principles
This is mainly embodied in two aspects: first check the external conditions are appropriate, on the other hand is to avoid random unsealed, disassembly, this can avoid failure of enlarge or reduce the precision of the system.
(4) after the first general special principles
When the discharge breakdown.Should first consider the most common reason, based on the analysis of special rarely happens.
(5) in addition, you also need to follow after the first check electricity, after the first software hardware, first after the mechanical principle of electrical appliances and so on,the prospect of laser cutting machine for sale is very good.

Laser cutting machine safety operation procedures

Laser cutting machine at work, if the failure is very dangerous.Operators must strictly follow the safety of the laser cutting machine operation procedures, this is not only the need of personal and equipment safety, and guarantee the normal work of the laser cutting machine can, achieve technical performance.Give full play to its processing needs.Therefore, in the use and operation of laser cutting machine must strictly follow the safety operation procedures.
(1) must follow the machine safety operation procedures.
(2) must receive pre-job training, to learn the structure of the equipment,.Performance, be familiar with the operation procedures and qualified license can be independent operation.
(3) wear labor protection articles according to the rules in the vicinity of a laser beam must wear safety glasses.
(4) in not clear whether a material can be laser processing before, and not to the processing, so as to avoid the potential danger of smoke and steam produced.
(5) the operator shall not leave the job or when the device client escrow, is really necessary should stop when they leave.
(6) will put a fire extinguisher available and where not to turn off the laser processing or brake light, don’t place in the vicinity of laser beam without protection of paper, cloth or other fuel.
(7) maintain laser, the lathe bed and the surrounding site neat, orderly, no oil, artifacts, plank, waste stack according to regulations,the prospect of laser cutters for sale is very good.
(8)Use cylinders, should avoid to crush wires or trachea, so as to avoid leakage gas leakage accidents.Cylinders use, transport shall comply with the rules of the cylinders, cylinders are forbidden from sunlight or near the heat source, when you start the cylinder valves, the operator must stand in the bottle mouth side.

Laser cutting machine internal schema attribute

Laser cutting machine internal model properties have some such factors so the cavity was analyzed using the scalar wave equation.Laser cavity is sometimes referred to as the law in the cloth – perot cavity due to the method of in – perot interference in their similarities.However, in the cloth – perot interferom – eters has a separation distance than to end the size of the reflector is much smaller.Method in the cloth – perot interferometer patterns in the diffraction properties of different laser cutting machine internal model properties.A basic understanding of the analysis of the laser resonant mode.The pattern of solid and gas laser yes equation solution.(1.28 a) and (1.28 b), known as the gaussian model.They are patterns of transient electromagnetic method.Analysis of gaussian beam optics and laser mode form good math skills demonstration in the chapter 1.It is also important is to learn the mathematical analysis of the following two reasons:
(1) we will appreciate the limitations and conditions, you can use the gaussian model;
(2) we will know how to apply these mathematical techniques to the new structure.the prospect of laser cutter machine for sale is very good.

Categories

Recent Post

Revolutionizing Our Workshop with Reaying’s Fiber Laser Cutting Machine

How Reaying’s CNC Lathe Transformed Our Precision Machining Capabilities

The Future of Cleaning: How Reaying’s Fiber Laser Cleaning Machine Revolutionized Our Operations

My Experience with the Reaying Fiber Laser Welding Machine

My Experience with a CO2 Laser Engraving Machine

Tag Cloud